1
Messages
This section allows you to view all Messages made by this member. Note that you can only see Messages made in areas you currently have access to.
Messages - EJYT
2
Mk2 Golf Chat / Re: Heritage uprated headlight wiring loom
3
Mk2 Golf Chat / Re: Heritage uprated headlight wiring loom
4
Mk2 Golf Chat / Re: restoring engine company in Hampshire
5
Suspension & Steering / Suspension rebuild coming up...
Engine all rebuilt meantime and ready to go (fingers crossed it starts). Front seats at the trimmers.
Next job when it arrives is on to the two post lift for all the suspension off to blast and repaint that.
Is there perchance a sequence published somewhere for stripping front and rear suspension, replacing the bushes and then refitting it all?
Thanks in advance.
6
Engine & Gearbox / Re: Flywheel cover plate - open area
I'm still wracking my brains how to make this plate cover fit. Eddypeck, your diagrams were very informative, except that I couldnt find my one-piece plate cover. Its a KR engine and a 020 gearbox for a 16v. I think im going to have to split them to find the part number of my plate, and maybe make up a plate to cover the last hole. Puzzling.
7
Interior, Upholstery & Trim / Re: Badges!?
The badges for 5 and 7 slat grills are NOT interchangeable. If you have a 7 slat grill you need and early badge.Thanks
Anyone got an early 16v badge?
8
Interior, Upholstery & Trim / Re: Badges!?
9
Engine & Gearbox / Re: Flywheel cover plate - open area
https://photos.app.goo.gl/ffHKyy5MgfARWVgk8
but im damned if i can work out from the photos what the problem might be. Anyone else got a one-piece flywheel cover plate like this? How is the last gap covered behind the driveshaft flanges?
https://photos.app.goo.gl/9VSGdiXFxS67xWsCA
10
Engine & Gearbox / Re: Flywheel cover plate - open area
These diagrams show in great detail a KR engine with a split two-piece flywheel cover plate (45 and 45A), (plus this small extra cover plate for the prop shaft gap - 49).
http://www.oemepc.com/vw/part_single/catalog/vw/markt/RDW/modell/GO/year/1991/drive_standart/110/hg_ug/103/subcategory/3002/part_id/3685688/lang/e#sec_29
But my engine has a slightly different one-piece plate. Pictured when dismantling.
https://photos.app.goo.gl/a8EYCZsvS67r1Lor8
I wonder if mine has a smaller gap, or a different design. Does anyone else recognise this end-plate design?
Like I said, I don't remember taking a small plate off around the shaft output (but I guess my memory isn't infallible evidence!)
I think I might have to pull the gearbox back off to find out if there's another way or something i've missed. Ah well, i'll maybe get better each time!
11
Engine & Gearbox / Re: Flywheel cover plate - open area
12
Engine & Gearbox / Flywheel cover plate - open area
I've reassembled my engine and attached it to the gearbox. There's a small uncovered gap left in the flywheel cover plate attached to the engine just at the back behind where the drivers side driveshaft exits the gearbox. I assume this is put on afterwards to allow the driveshaft flange to slide past the cover plate when mating or splitting the engine and gearbox. (Pictured here)
https://photos.app.goo.gl/RcgR2rkCB1vi7F6Y7
I dismantled the engine myself originally but cant remember taking a cover off, and cant find anything in my bits and peices - labelled or unlabelled - that looks like it fits this gap.
I asked Matthew Palmer if he had a plate and he has sent me one that looks close to whats needed (pictured), but doesnt look like its the right one.
https://photos.app.goo.gl/9EimyxvPnehcLhne7
I think i need a plate with two bolt holes, but I'm not sure. Maybe I've just done it all in the wrong order and I need to split them again.
Can anyone please advise me?
Thank you in advance.
Eddie
13
New Members Say Hi! / Re: New member with Golf Ryder
14
Mk2 Golf Chat / Re: Con Rods
15