31
Messages
This section allows you to view all Messages made by this member. Note that you can only see Messages made in areas you currently have access to.
Messages - cupracraig
32
Members' Cars / Re: CupraCraigs 20v Project
IMG_20210223_163144 by Laxadams, on Flickr
IMG_20210223_170640 by Laxadams, on Flickr
IMG_20210223_171826 by Laxadams, on Flickr
33
Members' Cars / Re: CupraCraigs 20v Project
They look great!
Did you paint them?
Yeah just masked them up, rubbed down with some 400 grit and then primed and painted.
i have seen that you can buy brand new ones and just to add to the general clean look of the car i might buy a set. I could make up another loom for these and sell as a nice working set
34
Members' Cars / Re: CupraCraigs 20v Project
Guages are all working as expected.
New / additional temp sender ordered so both MFA and VDO's report on oil temp.
too cold on the weekend to work on it any more
IMG_20210214_132028 by Laxadams, on Flickr
35
Members' Cars / Re: 1986 8v GTI restoration - You may recognise this one!
36
Mk2 Golf Chat / Re: Mk2 restore
37
Members' Cars / Re: CupraCraigs 20v Project
That looks fantastic!
cheers dude, cant wait to drive it again. Hopefully i can comve visit you and pick your brains on Diffs!
I did a few more bits over the weekend.
I ran the lighting / fan power / altenator trigger wire looms through the chassis leg and connected them up
I had a look at the indicator loom and decided that i wanted to run it from inside the car, so rather than change it, i just made a brand new loom.
IMG_20210205_174119 by Laxadams, on Flickr
bit of a loom making selfie so some of you can put a face to the name:
IMG_20210205_164222 by Laxadams, on Flickr
i've also ordered a load of LED bulbs to replace the older style ones, so everything will be LED bar the headlight and fog light bulbs as having a strong white light from those i feel would look out of place
38
Members' Cars / Re: CupraCraigs 20v Project
IMG_20210129_172948_780 by Laxadams, on Flickr
IMG_20210129_175849_302 by Laxadams, on Flickr
I installed the dash yesterday and started to run the internal loom through the gaps
IMG_20210203_181508_799 by Laxadams, on Flickr
39
Members' Cars / Re: CupraCraigs 20v Project
Tach adapter plumbed back in and running
IMG_20210104_214051 by Laxadams, on Flickr
Interested in the tach adapter, is it suitable for a v5?
I don't see why not, as long as your ECU has a tach signal output it just amplifies it for the dash.
Just another level with the wiring / braiding... amazing!
Thanks, most of the engine loom and light loom has been done, so it looks really good and protects it well
40
Members' Cars / Re: CupraCraigs 20v Project
IMG_20210104_214051 by Laxadams, on Flickr
Braiding all the wires now:
IMG_20210123_210731 by Laxadams, on Flickr
Made a new foglight loom:
IMG_20210124_220337 by Laxadams, on Flickr
IMG_20210128_225600_858 by Laxadams, on Flickr
cleaned out the brake fluid res, looks much better now
IMG_20210129_081804 by Laxadams, on Flickr
41
Members' Cars / Re: LUCY ‘91 Mk2 Golf GTI Alpine White
42
Members' Cars / Re: CupraCraigs 20v Project
Cracking project mate! Where did you get the bracket for the radiator fan, is it a custom effort?
it was just a universal one on Ebay, the single fan is more than enough on these cars
43
Members' Cars / Re: CupraCraigs 20v Project
That underlay looks good stuff, is it rubber backed (easy to cut)?
I was using a bitumen backed one on the Pug and it was borderline too tough to cut to shape, never again.
its got a latex backing, i went through a few stanley knifes cutting it as the wool blunts the blades
44
Members' Cars / Re: CupraCraigs 20v Project
then realised that the engine loom has to come back into the car to the ECU not just the bit for power etc.... so started to strip that down and get that into a position to be able to move that into the car.
Been doing some bits but forgot to take many photos.
Fusebox to engine loom extended just to make it all much easier to route internally.
Engine loom looks much tidier now
Battery cables ran but will need to decide on a new battery and how i'm going to secure it in the boot... i have got a false floor in there at the moment for the Sub, but i won't be running a stereo any more, so might re-make the floor and secure the battery to that.
IMG_20201218_145924 by Laxadams, on Flickr
IMG_20201218_151432 by Laxadams, on Flickr
IMG_20201217_160620_758 by Laxadams, on Flickr
Modified the TIP, MAF and intake
45
Members' Cars / Re: CupraCraigs 20v Project
I used some insulation wool that i have to replace the thin and flimsy insulation where the dash sits
I used spray on contact adhesive in patches to secure the exhaust tunnel insulation and onto the dash top. if the dash makes any rattling sounds i'll be amazed!
firewall insulation cut and i'll put that in today, then i can get the heater installed.
Not sure if i should order up and fit the window now or have it be one of the last things i do